Skip Nav
JOHN DEERE - 635 Back
Request a Quote
Year :
2020
Condition :
New
Model Number :
635
Available Options
width
138

JOHN DEERE 635SIDE-PULL MOWER-CONDITIONERS

TURN 10-HOUR DAYS INTO 460-ACRE DAYS
John Deere Mower Conditioners are built with extra durable parts to withstand the tough conditions of everyday use. And with innovations like our cutterbar's patented shear hub, you can be sure that should you hit an obstruction, getting your machine up and running will be fast and painless.
Urethane roll conditioner available
Cutting platform is gear-driven
Adjustable gauge shoes
Flotation tires

READY. SET. GO!
When your hay is ready, and the forecast looks good, you want cutting done fast. Well you are in luck, because John Deere Rotary Mower-Conditioners let you zip through even tough cutting conditions.

The speed is yours for several reasons. Rotary discs, with a tip speed of 191 miles per hour (307.4 kph), zip through crop. The rugged cutterbar, and easy-to-adjust suspension system, lets you hug field contours, and move over rocks, and through softer obstructions like ant hills or varmint mounds.

Speed also comes from fast maintenance and easy adjustments to the cutterbar angle, the conditioning level, and windrow forming shields. No matter the crop conditions, or the field obstructions, John Deere Rotary MoCos get you cutting fast.

FEATURES
CLEVIS HITCH
The clevis hitch is in base equipment. This design attaches directly to the tractor drawbar for operator convenience. The heavy-duty clevis design provides a strong attaching point to the drawbar.

For added convenience, the hitch-pin retaining bracket can also be used to store the power take-off (PTO) shaft when the machine is not attached to the tractor.

The clevis hitch is designed to be towed by a tractor only and includes a screw jack and safety chain.

Turn limiters may be required to prevent powerline damage if the hitch point of the tractor is beyond the rear drive wheels of the tractor.

EQUAL-ANGLE HITCH
The drawbar equal-angle hitch is optional equipment. This hitch option includes:
Ball-joint hitchto be installed on the mower-conditioner tongue
Tractor hookup
Drawbar extensionto be installed on the tractor drawbar and adjustable with one wrench
The drawbar equal-angle hitch is designed to be towed by a tractor only and includes a screw jack and safety chain.

Turn limiters may be required to prevent powerline damage if the hitch point of the tractor is beyond the rear drive wheels of the tractor.

An overrunning clutch is located near the platform gearcase. This design enables free rotation of the tractor hookup for easier attaching to the tractor.

A slip clutch is incorporated into the overrunning clutch to provide protection to the platform.

SWIVEL HITCH
For added maneuverability, the 630 and 635 Mower-Conditioners offer an optional rockshaft swivel hitch. Turn limiters are not required with the swivel hitch.

The swivel hitch is available in a 1000-rpm power take-off (PTO) only. It attaches to the lower lift arms of a Category 2 or 3N 3-point hitch with or without quick-hitch.

This option enables cutting square corners as well as making it easier to cut around field obstacles. Tractor hookup U-joint angles remain constant for reduced driveline noise and vibration in turns.

NOTE: If the platform is to be maneuvered while under power, it is recommended the rear powerline with single constant-velocity (CV) U-joint be ordered.

ROTARY DISK CUTTERBAR
The rotary cutterbar is designed and built by John Deere. Large oval disks with free-swinging knives are used to cut the crop.
All cutting disks are the same and are computer-designed for improved wear and cutting performance.
Cutting disks are made of high-strength, austempered steel to ensure the steel is thoroughly and evenly tempered for good wear characteristics.
The disks rotate to give a knife-tip speed of 307 km/h (191 mph) for clean cutting.
The knives are free-swinging to reduce damage if a solid object is struck, and they are reversible to double the useful life.
The knives are removed at the front of the cutterbar for convenience.

MODULAR-DESIGN CUTTERBAR WITH 3 YEAR WARRANTY
John Deere's patented design cutterbar is made from individual, diagonal-cut modules. Serviceability is easy. Modules can be removed individually while leaving the cutterbar attached to the frame.

Made of high-strength, nodular iron castings, each module consists of two idler gears and one drive gear. The large-diameter idler gears transmit power from module to module. The idler gears turn at a relatively slow speed for added durability.

The smaller-diameter pinion drive gear is used only to power the cutting disk. Power is not transmitted from one cutting disk to another except through the large-diameter idler gears. The modules are interchangeable. Disk rotation is determined by the position of the quill (A). There is a rubber oil seal between each cutting module.

CUTTERBAR PROTECTION
Steel runners are located under each disk. Right-hand and left-hand adjustable gauge shoes further protect the cutterbar.
The half-moon shaped disk protectors extend past the cutterbar module to protect the cutting disk.
The disk protectors are made of heat-treated boron steel, whose material characteristics are very similar to spring steel. Resistance to bending is nearly three times greater than molded ductile iron.
Knives rotate close to the disk protectors to give a good shearing action and help to keep the cutterbar clean.
Each cutting disk is attached to a driver (shearhub) on the splined pinion gear. The driver has part of its splines removed so it will shear if the cutting disk receives a severe impact.
The shear strength of the driver is designed to be just slightly less than that of the pinion gear.
Power to the disk is interrupted when the driver shears to protect the internal components of the cutterbar.
Damage is limited to exposed components and does not require disassembly of the cutting modules.
Power is transmitted through a U-joint to the first cutting disk.
The U-joint attaches with four bolts to the driver on the first cutting disk. No special tools are required to remove the first cutting disk.
The torque for attaching bolts is the same as for attaching the disk to the driver (149.1 Nm [110 lb-ft] compared to the 339 Nm [250 lb-ft] required to attach the driver to the pinion gear).

IMPELLER CONDITIONER
Impeller conditioning is standard equipment on all John Deere mower-conditioners. Proper conditioning in a wide range of crops can be achieved when the conditioner is properly adjusted. The impeller conditioner works well in legumes, especially alfalfa and most all-grass crops. Impeller conditioners are not recommended for thick-stemmed or cane-type crops, such as sudan or sudex, or crops over 1.5 m (5 ft) tall.

URETHANE ROLL CONDITIONER AVAILABLE
The 630 and 635 Side-Pull Mower-Conditioners and the 830 and 835 Center-Pivot Mower-Conditioners are available with a urethane roll conditioner. The urethane roll conditioner works well in legumes, especially alfalfa, and most all-grass crops. In general, roll conditioners are better suited for thick-stemmed, cane-type crops and crops more than 1.5 m (5 ft) tall.

MOLDED URETHANE ROLLS ARE FORMED BY A COOL MOLDING PROCESS THAT DOES NOT DISTORT OR WARP THE STEEL CORE OF THE ROLL:
This process ensures the rolls are straight and cylindrical, so they can be accurately spaced close together for uniform conditioning along the length of the roll.

An intermittent recessed cleat design gives more crimping edges for greater pressure per square inch, which results in superior conditioning and faster crop drying.

POWER IS DISTRIBUTED BY THE PLATFORM AND CONDITIONER DRIVE GEARBOXES:
Gearbox uses heat-treated, steel-forged spur gears for added strength.
Drive gears operate in a sealed environment to prevent excessive wear or contamination.
Telescoping drivelines ensure positive drive.
Spur gears have two to three teeth intermeshing at all times for a smooth, positive drive.

WINDROW FORMATION
Forming shields are easily adjusted to control material flow. This allows the operator to match the windrow width to harvesting requirements. A swathboard is in base equipment for additional control of the windrow formation (for 630 and 635 Mower-Conditioner models only).

V10 STEEL ROLL CONDITIONER
The V10 steel conditioner rolls feature 10 angled flutes arranged in a chevron pattern, or V-pattern, along the length of the steel core. Steel rolls offer improved wear life over urethane rolls, particularly in adverse crop conditions.

ADVANTAGES OF THE V10 CONDITIONER ROLL OVER THE PREVIOUS STRAIGHT FLUTE DESIGN ARE AS FOLLOWS:
More crimping edges for improved conditioning
Improved feeding
Improved windrow formation

WIDE SWATH KIT
The wide swath kit is a factory-installed option for the 630, 635, 830, and 835 Mower-Conditioner models.

When equipped with an impeller conditioner, the kit consists of a redesigned, base swath board and four (3.0-m [9.8-ft]) or six (3.5-m [11.5-ft]) steel vanes bolted to the bottom of the swath board.

On roll conditioner machines, the kit also comes with a redesigned, base swath board but has six (3.0-m [9.8-ft]) or eight (3.5-m [11.5-ft]) steel vanes.

When the forming shields are fully open, this kit will increase windrow width up to 25 percent over the base configuration of the machines.

Similar models may be shown in addition to the featured model. Equipment may be shown with options. Specifications are subject to change without prior notice.
Express Financing Get Pre-Approved
Get a FR8Star Shipping Estimate

Request a Quote
Year :
2020
Condition :
New
Model Number :
635
Request Information
Available Options
width
138
News

John Deere Spring Clinic Tuesday @ 8:30

John Deere Spring Clinic 2018 on Tuesday 8:30 Feb 27 at Cross Implement in Minier. Get the Latest Information on John Deere Equipment . Register to receive a $750 coupon for select John Deere precision ag products.
Read More

Looking to Roll Your Late Model Equipment | Over 150 1 Season Old Units in Stock

We Are the Largest Single John Deere Dealer Location in North America | Low Overhead + High Volume + Unrivaled Quality = Great Deal
Read More

See it. Drive it. Own it. Join us for Drive Green Demo Days

John Deere Equipment Ride and Drive At Cross Implement 703 S Minier Ave Minier IL 61759 Friday Jun 16 8:00am & 5:00pm Saturday Jun 17 8:00am to Noon
Read More